Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Fence Installation: The Riverside Owner’s Guide
Schluter fence installation in Riverside typically costs $3,500 to $9,000 installed, depending on linear footage, substrate condition, and whether we’re replacing an existing failed product or starting fresh. We stock Schluter-compatible trim, edging, and drainage profiles on our trucks, and most fence and edging jobs we complete in one to two days. Owners usually discover a problem the same way: a corner piece has lifted, water is pooling where the fence meets a walkway, or the profile has separated from the substrate after a Riverside summer heat cycle.
Schluter products are built around a simple idea: manage water at the transition. When the fence profile or edge trim fails, the failure shows up at the joint first. You’ll see it before you feel it. If you’re standing in your driveway looking at a lifted Schluter edge and wondering whether it’s a five-minute fix or a full replacement, this page gives you the straight answer.
Which Schluter Models This Applies To
We install and replace the full Schluter exterior line: Schluter-SCHIENE, Schluter-JOLLY, Schluter-DILEX, Schluter-BARA, and Schluter-TROBA drainage profiles, along with Schluter fence transition pieces where the profile meets a post or gate footing. The gotcha most Riverside homeowners hit is this: Schluter profiles are not universal across series. A DILEX-EKE movement joint profile will not swap cleanly into a DILEX-AHK application without reworking the reveal. We verify the series by the stamped code on the flange before we quote anything. If the flange is buried under thinset or soil, we measure the visible face width and pull the profile spec to match it.
On the OEM-vs-aftermarket question: Schluter’s own profiles are aluminum, stainless steel, or rigid PVC, depending on the series. Aftermarket equivalents exist, but the anodizing thickness on the Schluter aluminum is the spec that matters outdoors in Riverside. Thin aftermarket coating fails in two to three summers here. We install Schluter product unless the series is discontinued, and then we tell you before we order it.
We’re an independent contractor in Riverside, not a Schluter dealer or factory affiliate. We install their products because the spec is consistent and we can stand behind the work with a written guarantee.
Styles & brands we work with
Signs Your Schluter Fence Installation Is Failing
- The profile has separated from the substrate at the corner. This is almost always a bond failure from movement. Riverside’s clay soil expands and contracts through wet and dry seasons, and a rigid profile anchored to a moving slab will eventually pop at the stress point.
- Water pools at the fence transition instead of draining. The Schluter-TROBA or drainage pathway is clogged or was pitched incorrectly at install. Standing water accelerates corrosion on the aluminum face and undermines the bond line beneath the profile.
- Visible oxidation or pitting on the exposed face. Coastal-adjacent air and Riverside’s summer UV will expose a cheap coating fast. Factory Schluter anodizing holds; failed aftermarket coating shows pitting within 24 to 36 months.
- The edge piece is bent or dented from impact. Lawn equipment, a sliding gate, or a vehicle bumper catches the edge and deforms the profile. Once the profile is kinked, water gets behind it and the failure spreads along the run.
- You hear a rattle or click when you step near the profile. That’s the profile moving against the substrate. The mechanical anchor has failed, and the movement will only get worse as the seasons cycle.
Replacement Cost & What’s Included
Installed Schluter fence and edging replacement in Riverside runs $3,500 to $9,000. Here’s what drives the spread:
- Linear footage: a 40-foot fence transition is a $3,500 to $5,000 job. A 150-foot run with multiple corner pieces and gate transitions lands at $7,000 to $9,000.
- Substrate condition: if the concrete or masonry beneath the profile is cracked, heaving, or has lost its top surface, we repair the substrate first. That adds material and labor hours.
- Profile series: aluminum SCHIENE and JOLLY profiles are less expensive than stainless DILEX movement joints. The series you have determines the part cost per linear foot.
- Removal of the failed product: pulling a bonded profile without damaging the slab takes time and care. We quote removal separately so there’s no surprise in the final number.
Every quote is a written line-item price. Materials, labor, removal, and disposal are broken out. You’ll know what each linear foot costs before we start. The work is covered by our 365-Day Done Right Promise: if the installation fails within the first year, we return and correct it at no charge. That promise is in writing, on the quote and on the final invoice.
No part of this job is priced at the door. The number we quote is the number you pay. That’s The Garrison Standard, and it applies to every Schluter fence installation we do in Riverside.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check a few things yourself: run your hand along the profile to feel for lifted edges, look for standing water at the transition, and note whether the movement is localized or running the full length. What you shouldn’t do is grab a pry bar and start pulling. A bonded Schluter profile under tension can release suddenly, and the edge is sharp enough to open a hand. We’ve seen it happen.
The bigger reason DIY fails on this part is the pitch. A Schluter drainage profile only works if the angle is right and the bond line is continuous. If you re-set the profile at the wrong slope, you’ve spent a Saturday and the water still pools. That’s a repair we get called to fix after the homeowner tried it once. Call us at (424) 567-8472 before you break out the tools, and we’ll tell you straight whether it’s a repair or a replacement.
FAQs
A properly installed Schluter exterior profile on a stable substrate lasts 15 to 25 years in Riverside. The profile itself will outlast the bond line in most cases. The failure you’ll see first is usually from substrate movement or water intrusion at a seam, not the material degrading. Call (424) 567-8472 and we’ll assess your specific installation.
Yes, if the failure is localized to a single joint or corner piece, we can remove that section, clean the substrate, and re-set a new piece. If the profile has separated along multiple sections or the substrate is moving, a full replacement is the honest fix. We’ll show you both options in the written quote.
Most Schluter fence and edging replacements in Riverside take one to two days on site. Removal of the failed profile is usually the slowest part. We schedule the work in sequence so the site is clean and the new profile is fully set before we leave.
We carry the most common Schluter exterior profiles in aluminum and PVC on our trucks: SCHIENE, JOLLY, BARA, and TROBA in standard lengths. If your series isn’t on the truck, we order it from our Riverside supplier and it’s typically on site within three business days. We’ll tell you which applies before you commit to anything.
Contact Bradford Remodeling Co Riverside
If you’re looking at a failed Schluter fence profile in Riverside, call us at (424) 567-8472. We’ll ask you for the series code if it’s visible, the linear footage of the run, and whether you’re seeing movement or just cosmetic wear. Then we’ll give you a written estimate with real numbers. Straight number, real scope, no surprises at the final walk.
Written by Curtis Lane, Owner, Bradford Remodeling Co Riverside at Bradford Remodeling Co Riverside, serving Riverside and nearby areas.
