Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Riverside Owner’s Guide
We install Boral fence systems in Riverside for $3,500 to $9,000, depending on the panel count, post depth, and gate hardware involved. Most replacement runs we do start with a homeowner noticing a cracked post or a panel that’s started to sag at the bottom rail during the dry season. Boral is a poured-composite product, not vinyl, and it fails differently than cheaper material does in Riverside heat. When it goes, it usually goes at the connection points first.
Which Boral Models This Applies To
Boral’s fence line runs under a few product names that all share the same composite formulation. The key is matching the rail profile to the original post mortise, because Boral posts are routed differently than standard vinyl posts. If your posts are still square and plumb, we can often swap just the rails and pickets. If a post cracked, we’re pulling it and setting a new one in fresh concrete. The model number is typically stamped on the back side of a rail or inside the post cap, but most Riverside fences we see are either the Tuscany or traditional 6-foot privacy profile. One gotcha we run into constantly: Boral’s 5/8-inch picket thickness is not interchangeable with the 1/2-inch pickets on standard vinyl fence. If a homeowner tries to wedge a generic picket into a Boral rail, it binds, then it buckles, and then they’re calling us anyway. Aftermarket equivalents exist, but in Riverside’s 100-degree summers, the OEM composite is what actually holds its shape. We stock Boral rails, pickets, post wraps, and lattice toppers on the truck, and we can order the full panel sheets when the job calls for it.
Styles & brands we work with
Signs Your Boral Fence Installation Is Failing
- Post lean or base cracking. This usually means the concrete footing shifted after a heavy rain season, or the post was set too shallow. A $700 post replacement is always cheaper than a $4,000 panel run that fell over.
- Rails pulling out of the posts. The mortise slots hold rails by friction and small screws. Riverside’s dry-season heat cycles expand and contract the composite, and eventually the screw seats strip. We remount and re-seat the rail, or replace it if the slot is torn.
- Pickets warping or bowing. Boral pickets are dense and should not bow like vinyl does. If you’re seeing a wave across a run, the rails were spaced wrong at install or the fence sustained wind load beyond what the design handles.
- Bottom rail rot at the ground line. Even composite can wick moisture through end cuts that weren’t sealed. In Riverside’s sprinkler-heavy yards, this is the most common failure point.
- Gate sagging or dragging. The post supporting the gate has moved, or the hinge screws have wallowed out. This is a hardware and post fix, not a panel replacement.
Replacement Cost & What’s Included
Full Boral fence installation in Riverside runs $3,500 to $9,000, which includes removing and hauling the old fence, setting new posts in concrete, and installing the full rail-and-picket system. The range is driven by linear footage, gate count, and access: a 50-foot run in a flat backyard near the Victoria Avenue corridor prices differently than a 150-foot run with a side-yard gate and a slope. We write the price before any work starts, and that number does not move. Every Boral fence we install carries our 365-Day Done Right Promise: if a post shifts, a rail pulls out, or a gate starts dragging inside that first year, we come back and correct it at no charge. Materials carry Boral’s manufacturer warranty, and our labor is covered by the written guarantee.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can check a few things yourself before you call. Look at the post bases for hairline cracks. Walk the line and see if any rails have backed out of their slots. Grab the gate by the hinge side and lift: if it moves up more than a quarter inch, the hinge screws are letting go. There’s no high-tension component on a Boral fence, so a visual check is safe and simple. Where DIY goes wrong is in the concrete work and the post setting. A post that’s set 18 inches deep in Riverside clay won’t hold the same as one set and braced to code. And mixing Boral’s composite with parts from a home center void’s the manufacturer warranty. If you’re looking at anything beyond a loose picket, call us at (424) 567-8472 for a straight number. It costs nothing to price it out.
FAQs
In Riverside’s climate, a properly installed Boral fence typically lasts 20 to 30 years before posts need resetting or rails need replacement. The composite itself does not rot like wood, but the fasteners and the concrete footings wear out first. We see more failures from sprinkler over-spray and shallow post holes than from the pickets themselves. Call (424) 567-8472 for an exact assessment of your fence.
No. Once a composite post cracks, it has lost its structural stiffness, and patching it with epoxy or a post wrap leaves a weakened column that will keep moving. We pull the post, set a new one, and re-hang the existing panels. The fix usually runs less than a full replacement because the panels and rails are still fine.
A typical residential Boral fence installation, including demolition and concrete work, takes one to three days. Post-setting alone needs time for the concrete to cure before we load the rails and pickets, so you’re looking at a two-day job for most backyards. We keep the schedule tight and tell you the day count in writing before we start.
We keep stock of Boral rails, pickets, post caps, and lattice toppers on our trucks for single-post and small-run repairs. Full panel runs and custom gate frames go through our supplier and arrive within a week. If you need a specific profile or color matched, call (424) 567-8472 and we’ll confirm the part number before we quote.
Why Riverside Homeowners Use Bradford Remodeling
Curtis Lane grew up in Los Angeles and learned the trade at Los Angeles Trade-Technical College before spending the better part of three decades running crews across Southern California. He and his team have been working Riverside for years, on projects from wood-frame additions near the Victoria Avenue corridor to full kitchen rebuilds in Hawarden Hills. His jobs run in sequence, subs show up when they’re scheduled, and the punch list doesn’t close until the walkthrough is done. That discipline is what The Garrison Standard is built on: a written price before anything starts, background-checked and uniformed technicians on site, a live person answering the phone around the clock, and the 365-Day Done Right Promise behind every project. Straight number, real scope, no surprises at the final walk.
Need a Boral fence installed or repaired the right way? Call Curtis and the team at Bradford Remodeling Co Riverside at (424) 567-8472 for a free estimate and a written quote before any work starts.
Written by Curtis Lane, Owner, Bradford Remodeling Co Riverside at Bradford Remodeling Co Riverside, serving Riverside and nearby areas.
